Test Electronics

Click here to access our
Test Electronics ATE Software.


Enter
Login

Forgot Password?
Login
Recover Password | Forgot your password? Recover it here.
Get Password Return
 
Request Login | Not yet resgistered? Sign-up here. | delete account.
Register
Test Electronics

Tektronix S-51 - Trigger Countdown Head

All Used Test Equipment
Tektronix S-51- Trigger Countdown Head

Trigger Signal 25 picosecond Risetime    200 mV trigger output into 50ohms    industrial

The S-51 Trigger Countdown Head is a high-speed, tunnel-diode trigger generator. The S-51 generates a trigger output from an input waveform. Trigger output allows operation with sequential sampling systems. 25 ps pulse risetime. 200 mV trigger output into 50ohms. Variable Sync. Input SMA 5Vpp max. Output BSM.

Similar Items and Accessories

Tektronix 067-0572-01- Normalizer Head

Calibration Fixture    Vertical Sampling Heads    industrial

The 067-0572-01 Normalizer Head is a calibration fixture that is designed for use with vertical sampling plug-in units that utilize sampling heads.
Tektronix 7633- Storage Oscilloscope Mainframe

100MHz / 1GHz     10 mV/div    industrial

The 7633 Storage Oscilloscope Mainframe provides a 100MHz, three compartment mainframe for the wide range of Tektronix 7000-Series plug-ins. The instrument has three display modes and four storage modes. The maximum writing speed of 1000cm/us is achieved in reduced scan mode. (Plug-ins shown above sold separately.) Sensitivities to 10 mV/div are available at 100MHz while 1GHz bandwidths can be achieved using the 7A21N direct plug-in. Sweep speeds up to 500 ps/div are available using the appropriate time base plug-ins. Using the P6201 FET probe, a high impedance with 900MHz bandwidth is possible.
Tektronix 7S11- 14GHz Sampling Unit

14GHz    2mV to 200mV/div    industrial

The 7S11 Sampling Unit uses plug in heads ranging in bandwidth to 14GHz. The 7S11 is a single-channel vertical module using the sampling plug-in head concept for 7000-Series sampling oscilloscope systems. The 7S11 can be used in a variety of configurations. Use with a 7T11A sampling timebase module for one channel, Use two 7S11's with one 7T11A for dual channel sampling. Use two 7S11's together (without a 7T11A) for X-Y operation. 2 to 200mV/div Calibrated Deflection Factors. Delay Range: A 10 ns delay range is available for comparing two signals in a dual channel combination. Vertical Signal Out: 200 mV per displayed division within ±3%. (source is 10Kohms). DC Offset Range: +1 to -1 VDC. Bandwidth and Input Z: Determined by the S-Series sampling head.
Tektronix S-4- Sampling Head

DC to 14GHz    +1.0V to -1.0V    industrial

The S-4 Sampling Head is a 25ps risetime unit. DC to 14GHz, 50 ohm input impedance. Variable DC Offset allows signals between +1 V and -1 V limits to be displayed at 2 mV/div. Displayed noise is < 5 mV unsmoothed, 2.5 mV smoothed. Bandwidth: DC-14Ghz. Risetime: 25ps. Displayed Noise: <5mV. Signal Range: +1Vto-1V. Input: Z=50ohm, Vmax=+/-5V. Input Connector: SMA (3mm).
Tektronix S-51- Trigger Countdown Head

Trigger Signal 25 picosecond Risetime    200 mV trigger output into 50ohms    industrial

The S-51 Trigger Countdown Head is a high-speed, tunnel-diode trigger generator. The S-51 generates a trigger output from an input waveform. Trigger output allows operation with sequential sampling systems. 25 ps pulse risetime. 200 mV trigger output into 50ohms. Variable Sync. Input SMA 5Vpp max. Output BSM.
Content

Thank you for contacting Test Electronics.

Your responses will guide us in developing future products and
providing excellent customer support.

Please rate our service on the following aspects:

Service Excellent Very
good		 Good Average Poor Didn't
notice
Products
Product Documentation
Technical Support
Applications Engineering
Website Content

What are your reasons for visiting our site today?

Product information Pricing information
Technical support information Other

What products are you currently in the market for?

What changes or additional products would you suggest?


Content

This is your Personal Notepad

Put notes in here as you browse our website for future reference.

Next Clear
Content

Get and Instant Product Price Quotation.

We hope to beat or meet your cost expectations.

Enter circuit board size:
Select Number of Sides to Probe:
Enter Number of Test Pins for each side:
BOT TOP BAK FNT LFT RGT
Leave unused sides blank
Press Plate Features:
Press Rods Edge Press Adjustable
BON Plate Features:
Standard QuickChange Adjustable
Durability:
50 Thousand 2 Million 10 Million
  50K Operations = 2 years at 100 tests/day 2M Operations = 8 years at 1000 tests/day 10M Operations = 10 years at 4000 tests/day
Additional Features:
Lever Latch Panel Inserts
Microcontroller Mid Carrier Plate
HV Shield RF Shield
Estimate Price and Availability
Estimate Price and Availability
Enter carrier pallet size:
Select Base Material Type:
Pallet Material   Antistatic / Reflectivity:
No Carbon
White		 HighCarbon
Black		 Med Carbon
Grey
Material Thickness:
3mm 5mm
Hold Down Mechanism:
None SwivelLatch TensionPins
Durability Until Delamination:
12 Thousand 25 Thousand 50 Thousand
  12K Cycles = 6 months at 100 cycles/day 25K Cycles = 1 year at 100 cycles/day 50K Cycles = 2 years at 100 cycles/day
Pallet Material Durability:
Aluminum Stainless Titanium
Material Thickness:
0.0625inch 0.090inch 0.125inch
Hold Down Mechanism:
None SwivelLatch TensionPins
Additional Features:
Anodize Acid Etch
BeadPolish HeatTreat
Pallet Material   Conductivity:
No Carbon
NonConductive		 Silicon Carbide
Semiconductive
Material Thickness:
2mm 3mm
Durability from Stress Pulveration Fractures:
1 Million 1.2 Million 2 Million
  1M Cycles Standard HS Machining 1.2M Cycles Bead Polished Finish 2M Cycles Polish & Heat Temper Treatment
Estimate Price and Availability

Submit