Tektronix FG 5010- Programmable 20MHz Function Generator Plugin0.002Hz to 20MHz 20 Vp-p into 50-ohms industrial
The FG5010 Function Generator is designed to operate in a TM 5000-Series Power Module. The unit covers the frequency range from 0.002Hz to 20MHz while offering an output to 20 Vp-p from 50-ohms. Available waveforms include sine, square, triangle, pulse, and ramp with 10 ns rise/fall time. Features 10 to 90% variable symmetry in 1% steps. It also provides trigger, gate, counted burst, AM, FM, and VCF modes. This unit is easy to use via the front panel or programmed via the IEEE-488 interface Frequency Range: 0.002Hz-20MHz. Output: 20 Vp-p into 50-ohms. Available waveforms: Sine, square, triangle, pulse, and ramp with 10 ns rise/fall time. Variable Symmetry: 10 to 90% in 1% steps. Modes: Trigger, gate, counted burst, AM, FM, and VCF. Program: Front panel or IEEE-488 interface.Similar Items and Accessories
Tektronix DC 5009- 135 MHz Counter / Timer135MHz 2 Channel A/B industrial
The DC5009 Programmable Universal Counter / Timer provides 135MHz in both A and B Channels. The powerful reciprocal frequency measurement technique allows up to eight digits of resolution in less than 1 second. 135MHz Both A & B Channels. 10ns Single Shot Resolution. 8 Digit Display. 5ps Resolution with Averaging. Reciprocal-Frequency measurement. Auto or selected averaging to 108 in all modes. Duty cycle independent autotrigger. Probe compensation. High stability oven time base.
Tektronix DM 5010- Programmable Digital MultimeterAuto ranging A/C, DC, Ohms, Diode Math Functions, dB Calculation industrial
The DM5010 Programmable digital multimeter is a 41/2-digit autoranging Feature packed fully programmable digital multimeter. Double wide plug in module for the 5000-series mainframes. Full set of math functions with easy to use numeric keypad. Also programmable via GPIB. 41/2-Digits. Auto ranging DC Volts, Ohms, True RMS (ac or ac+dc). Diode Test. Comprehensive Math Functions. dB Calculations. Averaging Offset Scaling Hi/Low/Pass. IEEE-488.
Tektronix FG 5010- Programmable 20MHz Function Generator Plugin0.002Hz to 20MHz 20 Vp-p into 50-ohms industrial
The FG5010 Function Generator is designed to operate in a TM 5000-Series Power Module. The unit covers the frequency range from 0.002Hz to 20MHz while offering an output to 20 Vp-p from 50-ohms. Available waveforms include sine, square, triangle, pulse, and ramp with 10 ns rise/fall time. Features 10 to 90% variable symmetry in 1% steps. It also provides trigger, gate, counted burst, AM, FM, and VCF modes. This unit is easy to use via the front panel or programmed via the IEEE-488 interface Frequency Range: 0.002Hz-20MHz. Output: 20 Vp-p into 50-ohms. Available waveforms: Sine, square, triangle, pulse, and ramp with 10 ns rise/fall time. Variable Symmetry: 10 to 90% in 1% steps. Modes: Trigger, gate, counted burst, AM, FM, and VCF. Program: Front panel or IEEE-488 interface.
Tektronix MI 5010- Programmable Multifunction Interface PluginATE Automatic Test Equipment Data Acquisition and Generation industrial
The MI 5010 Multifunction interface system consists of the MI 5010 Multifunction Interface, and six different function cards. These cards are capable of a variety of functions typically required in ATE Automatic Test Equipment, and functional testing system interfacing, data acquisition and generation, and process control. MI 5010 shown with side panel removed. In addition to providing power to function, the MI 5010 has sequencing capability, time of day clock, command buffer, and self diagnostics. The MI 5010 houses up to three function cards, in any combination. The MI 5010 provides the communication between cards and the system controller such as the Tektronix PEP 301 or the 2402 TekMate. The MX 5010 extends the M1 5010 control to six function cards at one GPIB address. Easy GPIB programming is done in simple English. For example, "VOLT 1.25" sent to the Programmable voltage Source Card generates 1.25 volts across the 50M20's output pair. Similarly, "VOLT?" sent to the Analog Measurement card queries the 50M10 for the value of the last measurement. In addition to providing the Interface between the function cards and the system controller, the MI 5010 has a built-in command buffer. This buffer is capable of storing up to 300 system commands and executing them in sequence. These comands can be triggered by the on-board time of day, the internal clock, or signals from the system controller. This frees the controller to direct activity elsewhere in the system. Simple English Programming example: With an active 50M20 voltage source card, the following sequence of Simple English commands are sent to the MI 5010 buffer: BUFFER ON. VOLT 1.25. WAIT 2. VOLT -1.25. WAIT 8. EXECUTE 100. This EXECUTES 100 cycles of a signal toggling between 1.25 and -1.25 Volts with a duty cycle of about 20% and a period of about 1 second. The MI 5010 system also supports tightly coupled test sequencing to optimize measurement throughput. TTL compatible "Ready" and "Done" handshaking signals can be enabled to step test sequences with minimal dead time and without time consuming controller intervention in multi instrument configurations. Cards rapidly slide in and out of the MI 5010 system for a fast flexible approach to test. Alternatively, for dedicated applications, card configuration can be secured in the MI 5010 with rear locking screws. Programmable Stimulus and Measurement System. Controller-Free Test Sequencing using Internal Command Buffer. Analog and Digital lnput Output.
Tektronix TM5006- 6 Power Module Mainframe Benchtop Accepts 500 and 5000 Plugins industrial
The TM5006 Power Module Mainframe provides all power required for up to 6 single slot plug-ins. The TM5000 series mainframes are the IEEE-488 controllable versions of the TM500 series mainframes. The TM5000 series mainframe will accept both 5000-Series (IEEE-488 programmable) and 500-Series plug-ins. A wide variety of available plug-ins include signal generators, power supplies, oscilloscopes, counters, DMM's, etc. Forced-air cooling is standard. Available in both rack and bechtop versions. Build your own IEEE-488 Custom Test Equipment from the component level up! The 50M70 Developers card provides a complete 32 Data I/O interface to a breadboard on which you can solder or wire wrap you own circuit design. Combine this with the 50M40 relay scanner to multiplex inputs and outputs and a 50M30 digital I/O card which accepts data from pushbutton switches to quickly build your own tester by efficiently leveraging off all these readily available off the shelf products. Next build even more by plugging in any of the wide variety of industrial standard plug-ins including signal generators, power supplies, oscilloscopes, counters, DMM's, etc. Using these techniques you can quickly and easily build IEEE-488 based Automatic Test Equipment tailor made for your testing needs. To top it all off, this Tektronix plug-in module based industrial standard precision test equipment is fully supported by most local calibration laboratories around the world.Tektronix TM5006/10- 6 Power Module Mainframe Rackmount Accepts 500 and 5000 Plugins industrial
The TM5006 Power Module Mainframe provides all power required for up to 6 single slot plug-ins. The TM5000 series mainframes are the IEEE-488 controllable versions of the TM500 series mainframes. The TM5000 series mainframe will accept both 5000-Series (IEEE-488 programmable) and 500-Series plug-ins. A wide variety of available plug-ins include signal generators, power supplies, oscilloscopes, counters, DMM's, etc. Forced-air cooling is standard. Available in both rack and bechtop versions. Build your own IEEE-488 Custom Test Equipment from the component level up! The 50M70 Developers card provides a complete 32 Data I/O interface to a breadboard on which you can solder or wire wrap you own circuit design. Combine this with the 50M40 relay scanner to multiplex inputs and outputs and a 50M30 digital I/O card which accepts data from pushbutton switches to quickly build your own tester by efficiently leveraging off all these readily available off the shelf products. Next build even more by plugging in any of the wide variety of industrial standard plug-ins including signal generators, power supplies, oscilloscopes, counters, DMM's, etc. Using these techniques you can quickly and easily build IEEE-488 based Automatic Test Equipment tailor made for your testing needs. To top it all off, this Tektronix plug-in module based industrial standard precision test equipment is fully supported by most local calibration laboratories around the world. Option 10 = Rackmount.
